icstl23 Wrote:
-------------------------------------------------------
> Hi :)
> Sorry i can't find the post..
> And I run terminal in root..
>
> Now i'm here:
> Ther i a post about wrong wiki here :
> [forum.openwrt.org]
>
> So I had test other connection; that's what i
> found :
> in my hardware (V2.1) i receive correct message
> when i connect like this :
>
> [i.imgur.com]
>
>
> I receive that :
>
> U-Boot 1.1.4 (Jun 13 2014 - 15:14:01)
>
> ap135 - Scorpion 1.0DRAM:
> sri
> Scorpion 1.0
> ath_ddr_initial_config(178): (16bit) ddr2 init
> tap = 0x00000003
> Tap (low, high) = (0x0, 0x1d)
> Tap values = (0xe, 0xe, 0xe, 0xe)
> 64 MB
> Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1
> 0x17
> flash size 8MB, sector count = 128
> Flash: 8 MB
> Using default environment
>
> *** Warning *** : PCIe WLAN Module not found !!!
> *** Warning *** : PCIe WLAN Module not found !!!
> In: serial
> Out: serial
> Err: serial
> Net: ath_gmac_enet_initialize...
> athrs_sgmii_res_cal: cal value = 0x1
> No valid address in Flash. Using fixed address
> No valid address in Flash. Using fixed address
> ath_gmac_enet_initialize: reset mask:c02200
> Scorpion ----> S17 PHY *
> athrs17_reg_init: complete
> : cfg1 0x80000000 cfg2 0x7114
> eth0: ba:be:fa:ce:08:41
> eth0 up
> athrs17_reg_init_wan done
> SGMII in forced mode
> athr_gmac_sgmii_setup SGMII done
> : cfg1 0x800c0000 cfg2 0x7214
> eth1: ba:be:fa:ce:08:41
> eth1 up
> eth0, eth1
> Setting 0x18116290 to 0x58b1a14f
> Autobooting in 1 seconds
> ## Booting image at 9f020000 ...
> Uncompressing Kernel Image ... Too big
> uncompressed streamLZMA ERROR 1 - must
>
>
> RESET
> board to recover
>
> U-Boot 1.1.4 (Jun 13 2014 - 15:14:01)
> ...
>
> I was able to wrote tpl and hit, but nothing
> happened (I made out a will a lot of time..)
> I test with position the gnd in the other pin,
> it's the same
>
> Have you got an idea for resolve ?
Hi,
My TL-WR1043ND V2.1 is also bricked and i order a usb to tll cabel for serial, can you confirm that your schedule works? did it not needed vcc ? only rx, gnd and tx?
Thanks for your reply.
Greetings
Remco
-------------------------------------------------------
> Hi :)
> Sorry i can't find the post..
> And I run terminal in root..
>
> Now i'm here:
> Ther i a post about wrong wiki here :
> [forum.openwrt.org]
>
> So I had test other connection; that's what i
> found :
> in my hardware (V2.1) i receive correct message
> when i connect like this :
>
> [i.imgur.com]
>
>
> I receive that :
>
> U-Boot 1.1.4 (Jun 13 2014 - 15:14:01)
>
> ap135 - Scorpion 1.0DRAM:
> sri
> Scorpion 1.0
> ath_ddr_initial_config(178): (16bit) ddr2 init
> tap = 0x00000003
> Tap (low, high) = (0x0, 0x1d)
> Tap values = (0xe, 0xe, 0xe, 0xe)
> 64 MB
> Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1
> 0x17
> flash size 8MB, sector count = 128
> Flash: 8 MB
> Using default environment
>
> *** Warning *** : PCIe WLAN Module not found !!!
> *** Warning *** : PCIe WLAN Module not found !!!
> In: serial
> Out: serial
> Err: serial
> Net: ath_gmac_enet_initialize...
> athrs_sgmii_res_cal: cal value = 0x1
> No valid address in Flash. Using fixed address
> No valid address in Flash. Using fixed address
> ath_gmac_enet_initialize: reset mask:c02200
> Scorpion ----> S17 PHY *
> athrs17_reg_init: complete
> : cfg1 0x80000000 cfg2 0x7114
> eth0: ba:be:fa:ce:08:41
> eth0 up
> athrs17_reg_init_wan done
> SGMII in forced mode
> athr_gmac_sgmii_setup SGMII done
> : cfg1 0x800c0000 cfg2 0x7214
> eth1: ba:be:fa:ce:08:41
> eth1 up
> eth0, eth1
> Setting 0x18116290 to 0x58b1a14f
> Autobooting in 1 seconds
> ## Booting image at 9f020000 ...
> Uncompressing Kernel Image ... Too big
> uncompressed streamLZMA ERROR 1 - must
>
>
> RESET
> board to recover
>
> U-Boot 1.1.4 (Jun 13 2014 - 15:14:01)
> ...
>
> I was able to wrote tpl and hit, but nothing
> happened (I made out a will a lot of time..)
> I test with position the gnd in the other pin,
> it's the same
>
> Have you got an idea for resolve ?
Hi,
My TL-WR1043ND V2.1 is also bricked and i order a usb to tll cabel for serial, can you confirm that your schedule works? did it not needed vcc ? only rx, gnd and tx?
Thanks for your reply.
Greetings
Remco