Re: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Jan 1 00:00:49 OpenWrt syslog.info syslogd started: BusyBox v1.19.4 Jan 1 00:00:49 OpenWrt user.notice root: /bin/box_installer.sh : executing run_test Jan 1 00:00:49 OpenWrt user.notice root:...
View ArticleRe: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Hi, through you tries the file that tiggers the auto install is marked as done. run on your box: mv /mnt/usb/install/auto_package_done /mnt/usb/install/auto_package box_installer_start.sh Then the...
View ArticleRe: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Thank you Sir Matthias for the reply, I'll try it and feedback later.
View ArticleRe: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Thank you Sir Matthias it's up and running. I only have a problem for the minidlna, it still doesn't automatically run on boot. Is there a fix for this? Thank you.
View ArticleRe: IP resolving but Piratebox.lan does not
Hi shepbarrick, as I mentioned above, it is not always possible to help via teamviewer or skype. I think that your problem maybe be solved with some steps. But before we examine those, some...
View ArticleRe: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Hi, did you run the post installation steps with activating the minidlna? Matthias
View ArticleRe: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Yes Sir Matthias, Steps 5 and 6 of the post installation instructions. "5. Activate the UPnP Media Server by copying over the config file: cp /opt/piratebox/src/openwrt.example.minidlna...
View ArticleRe: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Hi, you should run /etc/init.d/minidlna enable since then, it is enabled to start at boot time Matthias
View ArticleRe: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Sir Matthias, I tried to run it on the box. The box boots normal at start with 4 lights (no led light for lan because I tried to connect on wifi), then after about 10secs the router would restart...
View ArticleRe: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Take the USB Stick to your computer and check if you have any filesystem errors.
View ArticleRe: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Sir Matthias, I've tried to plugged in my USB on my laptop and checked for file system errors. After doing so, no file system errors were found. I plugged the usb back to my box, normal boot again...
View ArticleRe: Help: PirateBox 1.0 Not Installed after firmware reflash (Failsafe Mode)
Hi, did you change/do anything else on the box? Set a static IP (192.168.1.2) to your computer, try to ssh the box using root@192.168.1.1 And please give me the output of the commands listed here:...
View ArticleRe: Returning MR3040 (or other TP-Link routers) back to original factory...
I do not remember what password i set for root, what can i do to reset root password so i can go about resetting to original firmware?
View ArticleRe: Returning MR3040 (or other TP-Link routers) back to original factory...
use failsafe mode to recover the password...
View ArticleRe: Returning MR3040 (or other TP-Link routers) back to original factory...
That is where i am having a problem, i turn the router on holding the button for 5 to 10 seconds and then i get no wireless connection to connect to. So i have tried the same with a wired connection...
View ArticleRe: Returning MR3040 (or other TP-Link routers) back to original factory...
[piratebox.cc] that did it, i was following a different guide that said to press the WPS/reset button straight away which doesn't work, you have to wait until it blinks.
View Articlemr3040 lights up thats it, the toggle is on 3G/4G
I got a little confused with instructions from davids page so as well as those instructions i looked the over as well! [www.disk91.com] 1. ssid? No, nothing. Phone, laptop, tower do not see it at all....
View ArticleRe: mr3040 openwrt not working
Having the same problem I chaged ip to static with portforward static ip tool and it said to choose 192.168.1.150 for preferred so i did!
View ArticleRe: mr3040 lights up thats it, the toggle is on 3G/4G
QuoteI got a little confused with instructions from davids page so as well as those instructions i looked the over as well! [www.disk91.com] outdated Quote1. ssid? No, nothing. Phone, laptop, tower do...
View ArticleRe: mr3040 openwrt not working
after a the installation, the piratebox is back at 192.168.1.1 again ! Quotem I chaged ip to static with portforward static ip tool and it said to choose 192.168.1.150 for preferred so i did! What is...
View Article