Hi,
I am trying to install pirate box in my TP-link tl-mr10u router. I installed openwrt which loads fine. But the installation of pirate box is stuck at creating swap file forever. The serial console output is-
I can see the USB flash drive mounting fine, but don't understand why it is stuck at creating swap partition. How can I solve this issue? Is there any manual partitioning option which might speed things up or solve this issue?
BTW, I like the idea of piratebox. Thanks! :)
I am trying to install pirate box in my TP-link tl-mr10u router. I installed openwrt which loads fine. But the installation of pirate box is stuck at creating swap file forever. The serial console output is-
Quote
6.880000] JFFS2 notice: (436) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead, 2 orphan) found.
[ 7.470000] SCSI subsystem initialized
[ 7.610000] usbcore: registered new interface driver usbfs
[ 7.610000] usbcore: registered new interface driver hub
[ 7.620000] usbcore: registered new device driver usb
[ 8.090000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.100000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 8.100000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 8.140000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 8.160000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 8.160000] hub 1-0:1.0: USB hub found
[ 8.160000] hub 1-0:1.0: 1 port detected
[ 8.270000] Initializing USB Mass Storage driver...
[ 8.280000] usbcore: registered new interface driver usb-storage
[ 8.280000] USB Mass Storage support registered.
[ 8.490000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 8.640000] scsi0 : usb-storage 1-1:1.0
[ 9.640000] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Blade 1.26 PQ: 0 ANSI: 5
[ 9.650000] sd 0:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 9.660000] sd 0:0:0:0: [sda] Write Protect is off
[ 9.660000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 9.690000] sda: sda1
[ 9.690000] sd 0:0:0:0: [sda] Attached SCSI removable disk
switching to jffs2
- init -
[ 28.670000] eth0: link down
Please press Enter to activate this console. [ 29.300000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
[ 29.310000] Backport generated by backports.git backports-20140124-0-g1256d3e
[ 29.530000] cfg80211: Calling CRDA to update world regulatory domain
[ 29.540000] cfg80211: World regulatory domain updated:
[ 29.540000] cfg80211: DFS Master region: unset
[ 29.550000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 29.560000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 29.560000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 29.570000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 29.580000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 29.590000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 29.590000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 29.680000] NET: Registered protocol family 10
[ 30.660000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 30.670000] cfg80211: Calling CRDA for country: US
[ 30.670000] cfg80211: Regulatory domain changed to country: US
[ 30.680000] cfg80211: DFS Master region: FCC
[ 30.680000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 30.690000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 30.700000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm)
[ 30.710000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[ 30.720000] cfg80211: (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[ 30.720000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm)
[ 30.730000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm)
[ 30.740000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 31.180000] loop: module loaded
[ 31.240000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 31.410000] nf_conntrack version 0.5.0 (455 buckets, 1820 max)
[ 31.640000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 31.910000] batman_adv: B.A.T.M.A.N. advanced 2013.4.0 (compatibility version 14) loaded
[ 35.010000] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
[ 35.020000] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities
[ 35.090000] EXT4-fs (loop0): recovery complete
[ 35.090000] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
[ 36.550000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 36.570000] device eth0 entered promiscuous mode
[ 36.570000] ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 37.550000] eth0: link up (100Mbps/Full duplex)
[ 37.550000] br-lan: port 1(eth0) entered forwarding state
[ 37.560000] br-lan: port 1(eth0) entered forwarding state
[ 37.560000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 37.570000] ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 39.560000] br-lan: port 1(eth0) entered forwarding state
[ 42.790000] Adding 32760k swap on /mnt/usb/external_fs/OpenWRT.swap. Priority:-1 extents:1 across:32760k
I can see the USB flash drive mounting fine, but don't understand why it is stuck at creating swap partition. How can I solve this issue? Is there any manual partitioning option which might speed things up or solve this issue?
BTW, I like the idea of piratebox. Thanks! :)