OPKG "No route to host"
Got through steps 1-14, skipped 15 as I followed step 1. But when I enter the commands into putty for step 2 of the pirate box set-up I get this: [imgur.com] I pinged google and it worked fine to my...
View ArticleRe: OPKG "No route to host"
Looks like your ping didn't reach google. If it did, you should get a response like: 64 bytes from 74.125.228.1: icmp_seq=0 ttl=51 time=178.072 ms Also, you're following an old tutorial. We have now...
View ArticleRe: Bricked MR3040
I have the same issue. Installed the firmware V2 from the factory and the device is now twinkling (lights on lights off every 2seconds)...I can post a video this afternoon after work if you want Matthias
View ArticleRe: Bricked MR3040
Hi, ok this looks like the stuff you flashed nearly bricked the device. Yes. :( It seems the uboot (bootloader) does still work, which means with a serial access you may recover it. If you think you...
View ArticleRe: Bricked MR3040
AAAAAA Thank's Matthias. I could not understand anything in the openWRT link. So, if I understand, the 3040 flashing is easier than the 3020 because we won't need to add a resistor. But we can use the...
View ArticleClik here to view.
Pirate box board issue (500 - Internal Server Error)
Hello, i'm trying to set up the forum on my pirate box. When i go to board/kareha.pl i have the following error: Any idea of what i did wrong ? excepting the forum the rest seem to work fine. edit:...
View ArticleProblem with install on MR3040 v1
I run on mac - and follow the DIY guide, but after the reboot, i get this : root@OpenWrt:~# vi /opt/piratebox/www/board/config.pl ~ ~ ~ ~ ~ ~ ~ ~ ~ - /opt/piratebox/www/board/config.pl 1/1 100% When i...
View ArticleRe: Bricked MR3040
I'd not need a reistor at the MR3020 nor MR3040. Let me know, If I can help. For european areas, I can offer a debrick help as well.. Matthias
View ArticleRe: Bricked MR3040
Hey ! It does not work for me at the moment. I cannot access the routeur. Here is what I did : Downloading tft Downloading openwrt generic v2 Change my ip adress to 192.168.1.2 Start tftp64 server...
View Articlestuck at step one of Post-Installation
so i did everything for the install and i think i got that much right. but I’m stuck at the post install stuff, i am using putty to ssh into my box and it is asking me for a password which i kind of...
View ArticleRe: stuck at step one of Post-Installation
Try telnet again and see if it works, maybe the password wasn't set correctly. If not, use Failsafe mode to recover the router and reset the password.
View ArticleRe: stuck at step one of Post-Installation
thanks it seems to be working now, i got the password reset and can log ssl into the modem, now i'm stuck at step two. it seems i'm really haveing a hard time with the post install part of this thing....
View ArticleRe: Pirate box board issue (500 - Internal Server Error)
Oh, that is weired. Try to reainstall the basic perl package opkg -d ext --cache /mnt/usb/install/cache/ install /mnt/usb/install/cache/perl_5.10.0-7_ar71xx.ipk If that won't solve it, we are forcing...
View ArticleRe: Problem with install on MR3040 v1
Hi, you box wasn't successfully installed, because the hostname was not set. Can you still telnet or ssh into your box? if not with a simple plug&play, try to setup a static IP on your client...
View ArticleRe: Bricked MR3040
Switch button is not needed. I'm only connecting TX -> RX RX -> TX GND -> GND After I established that, I power up my MR3040 with attached battery.. I left the board in the case-side with the...
View ArticleRe: stuck at step one of Post-Installation
Hi, sorry for the problems. Can you please post the output of the commands you find here Openwrt - troubleshooting That will help, Thanks Matthias
View ArticleRe: Problem with install on MR3040 v1
Yes i can ssh with the static 192.168.1.2 IP. On the drive old install log, i see a lot of warning and some drive error : Jan 1 00:07:14 piratebox user.notice root: * verify_pkg_installable: Only have...
View ArticleMade some mods and now PB won't start.properly.
I made some mods (Secured Directories, Exchange Upload Folder, Disable Shoutbox Reset). When I restarted I can connect to Piratebox but it won't open in the browser. I tried connecting via ethernet...
View ArticleRe: Made some mods and now PB won't start.properly.
Update, Am now able to ssh in both ethernet and wireless so I can now trobublesoot. Tom
View Article