TP Link MR3040 error
hi configured piratebox using MR3040. It got configured and was working. I wanted to change the USB and plugged in a new USB to the TP Link. I copied the install folder to the USB and accessed the TP...
View ArticleUnbrick a TP-WR1043ND v2
Hi everybody :) I had brick a TP-WR1043ND v2, and i found tutorials about unbrick this WR1043ND but only on the V1. - On Windows : [www.youtube.com] - On Linux : [forum.openwrt.org] - On linux in...
View ArticleRe: TP Link MR3040 error
Hi Rajesh ss :) Did you try the fail safe mode ? There is a topic about this here : [forum.openwrt.org]
View ArticleMR3040 original firmware
I was wondering how i turn the tp-link mr3040 back to the original firmware. Right now the usb files stick is gone so the pirate page don't even pop up anymore.. I try to follow the steps from...
View ArticleRe: Access piratebox through lan network
Matthias Wrote: ------------------------------------------------------- > I can advice you to a reconfiguration, but that > might turn you box unaccessable, if you do a > mistake. > >...
View ArticleRe: MR3040 original firmware
Are you using a static IP address for your computer when trying to ping the routers static address? i.e. 192.168.1.2 netmask 255.255.255.0
View ArticleRe: MR3040 original firmware
The USB stick is absolute necessary to run a PirateBox as crucial files are stoed on it. You can either search for it and continue using itor you can rewert to stock TP-Link firmware. The openwrt.org...
View ArticleLong, Delayed Start Due to eth0
Hi, I was wondering if anyone knew how to fix an issue I get on every boot. It delays startup by about 20 seconds each time: [ 9.570000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 28.550000]...
View ArticleRe: NEXX 3020 Piratebox
The mediatek devices run a different (CPU) Architecture then the PirateBox-custom images are built of. The PirateBox images contain an automatic installer which makes it as easy as possible to install...
View ArticleRe: Unbrick a TP-WR1043ND v2
Use Putty, and good luck ;) is this thread still relevant?
View ArticleRe: TP Link MR3040 error
Maybe you are running into a parition problem of the new USB stick. Can you try the old one again?
View ArticleRe: Access piratebox through lan network
You can look it up on the router, or you do uci set network.lan2=interface uci set network.lan2.ifname=$( uci get network.lan.ifname ) uci set network.lan2.proto=static uci set...
View ArticleRe: Long, Delayed Start Due to eth0
Does not you ethernet port work? Or what is the reason for digging into that topic? Usually those things are covered by the bridge interface later, see the output of the command ip addr #or ifconfig...
View ArticlePossibly Bricked my TPLink 3040-Fixed
Hello, new to forums and new to Piratebox. I just setup piratebox software on the TP MR 3040. I tried to change the SSID to something else through Vi. I then rebooted my router. After reboot, I could...
View ArticleRe: Unbrick a TP-WR1043ND v2
Hi Matthias :) This thread is always relevant. I bought this converter : [www.ebay.fr] I instal the driver, connect him & he is recognize. I have connected the router via putty for unbrick him....
View ArticleRe: How to Unbrick a TP-WR1043ND v2 - (overwrite the u-boot)
Ok, i found a message on [forum.openwrt.org] who said : i had overwrite u-boot. Do you know topic about rewrite uboot on this hardware ?
View ArticleRe: NEXX 3020 Piratebox
I see, I have just ordered a GL iNet box, in a few weeks it will drop in the mailbox ..
View ArticleRe: How to Unbrick a TP-WR1043ND v2 - (overwrite the u-boot)
?? uboot is working correctly ! Can you point me to th post? Only the flashed content has a defect. When you run linux, make sure you are running the serial terminal with write permissions, which...
View ArticleClik here to view.
Re: Unbrick a TP-WR1043ND v2
Hi :) Sorry i can't find the post.. And I run terminal in root.. Now i'm here: Ther i a post about wrong wiki here : [forum.openwrt.org] So I had test other connection; that's what i found : in my...
View ArticleRe: Returning MR3040 (or other TP-Link routers) back to original factory...
I try to restore TP-link 3020 v1 back to original fw but now LED light alway blink . Power, internal, wifi, Lan, WPS 1, 1, 1, 1, 1 1, 0, 0, 0, 0 1, 0, 0, 0, 1 1, 0, 0, 0, 0 Loop Someone have solution...
View Article