Re: MR3020 - Unable to connect to wget: bad address & no FTP
You are welcome. With posting the command output, it was pretty easy ;-) and saved much time. Have fun with your PirateBox (tu) Matthias
View ArticleRe: MR3020 - Unable to connect to wget: bad address & no FTP
I reformatted the USB device using Linux and made sure to select FAT32 this time. I then followed the instructions in the reflashing link you sent, and it all seemed to work perfectly fine, however...
View ArticleRe: MR3020 - Unable to connect to wget: bad address & no FTP
So did you replace the install folder with a fresh copy? It is important to wait a while after reflashing, it will take 3 or 4 additional reboots until everything is installed.
View ArticleRe: MR3020 - Unable to connect to wget: bad address & no FTP
Yes I re-downloaded everything, to make sure. I will post back in an hour if nothing has changed :)
View ArticleRe: MR3020 - Unable to connect to wget: bad address & no FTP
I was able to get it working this time after leaving it much longer, however the image forum appears as an index page listing just: Index of /board/ Name Last Modified Size Type Parent Directory/ -...
View ArticleRe: MR3020 - Unable to connect to wget: bad address & no FTP
this looks more like your board installation broke or isn't completed yet. Is the box still blinking regulary or are the LEDs steady for while. If last, you need to post the install.log best regards...
View ArticleRe: MR3020 - Unable to connect to wget: bad address & no FTP
The power button is on. The Internet light is flashing, slower than the WPS/RESET LIGHT. The WLAN light is off. The WPS/RESET light is flashing every second or so. If installation is still going can I...
View ArticleRe: MR3020 - Unable to connect to wget: bad address & no FTP
Patience is obviously a virtue. It's all working properly now thank you very much for your help.
View ArticleNeed help with installing on gl.inet router
I began installing the OpenWrt software to my GL.iNet router today and was successful, but after Step 1 of the Post-Installation, I could not figure out how to telnet into the router to continue...
View ArticleRe: Need help with installing on gl.inet router
Hi, yes, with deleting the USB content, you made it worse . :) Try this howto: Recovery with auto_flash best regards Matthias
View ArticlePlease help! Firmware issues TP Link 3020
Good afternoon, Firstly, I'd just like to thank you for all your efforts. I first came across PB around a year ago and have set up half a dozen units for various projects. Real fan. Now the issue....
View ArticleRe: need help. TP-Link MR3020
I seem to be having a similar issue Having successfully set up PB on both TP Link 3020's and 3040's a few months ago, I purchased a dozen for a new project. I lined them up on a bench and began the...
View ArticleRe: Please help! Firmware issues TP Link 3020
Hi, make sure, that the USB sticks are not only FAT32, but it must be partitioned with one partition in MBR mode, not GPT. This means, on linux (and openwrt) these USB must appear as /dev/sda &...
View ArticleRe: Need help with installing on gl.inet router
Thank you so much. I will try that as soon as I can. What a relief!
View ArticleRe: Please help! Firmware issues TP Link 3020
Many thanks Matthias, I'll format a stick again (I had previously used the SanDisk sticks but they were a different model (although I had formated them in the same way, I hand't checked the partition...
View ArticleRe: Please help! Firmware issues TP Link 3020
Hello I had tried using my mac (in Terminal) to format the USB drives, however, I noticed that they actually formatted them as DOS_FAT32. I didn't want to risk it again so downloaded and installed a...
View ArticleRe: Please help! Firmware issues TP Link 3020
Can you please post the output of: dmesg | tail -n 20 dmesg | grep sda ls /dev/sd*
View ArticleRe: Please help! Firmware issues TP Link 3020
What kind of power source do you use? Is it sufficient?
View ArticleRe: Please help! Firmware issues TP Link 3020
I have just spotted, that I have used a mixture. I have used the ones supplied but noticed that I had attempted to configure 2 units powered from the USB ports on the rear of my Mac display, and...
View ArticleRe: Please help! Firmware issues TP Link 3020
Here's a copy of the request output; BusyBox v1.19.4 (2016-01-26 21:26:14 CET) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | |...
View Article