Re: TP-Link MR3040 Installation Trials and Tribulations
Yup. You should try to reflash it with tftpd method.. but for that you need serial access to unbrick it. The following howto is for the MR3020 but describes exactly what need to be done to reflash via...
View ArticleRe: TP-Link MR3040 Installation Trials and Tribulations
Thanks I have ordered a ttl serial USB adapter. Should be here within the week Will let you know
View ArticleKnown hardware - firmware combinations
Hi, I created the following table, which came on my mind today at work: Firmware recommendations Please give me feedback, if something is missing, wrong. Anyone who has a wiki account is able to...
View ArticleRe: TP-Link MR3040 Installation Trials and Tribulations
Okay I have my USB Adapter lead its all connected and nothing is happening
View ArticleRe: TP-Link MR3040 Installation Trials and Tribulations
I have my adapter but nothing is happening It's wired up to pin 2-4 tx,rx,gnd I have the tftpd64 software running and it sees it, But when putty is run I get nothing.
View ArticleRe: TP-Link MR3040 Installation Trials and Tribulations
if you can't see anything during boot up you wiring is , maybe, wrong.
View ArticleRe: TP-Link MR3040 Installation Trials and Tribulations
Ok Looking at the board with Ethernet plug top left and on off switch at bottom, I have 4 cables in. And the battery. Reading the cables right to left (p1) red, green, yellow, black 3 Cables in USB...
View ArticleRe: The wiki layout NEEDS to be fix:X:Xed.
Sorry for the delay, deluged at work. Yes both have PB running, the special one for the 3040 also. I'm going to tackle the kahera board on both next. I also want to "customize" the look of the pages....
View ArticleRe: PirateBox + COPS (Calibre OPDS (and HTML) PHP Server)
ok so i figured out what i needed to do to get this installed. I edited the PB index.html file and linked it to index.php The only problem i having now is that once the browser opens up index.php it...
View ArticleRe: All installation instructions not working
I have had this Piratebox for a while.... So, the original image was likely out of date. Probably that is not an issue. However - with this new image and setup.... Everything works perfectly... UNTIL...
View ArticleRe: All installation instructions not working
I should add that I was trying to have this up and running at an event... so I think it times out after less than an hour or so of operation... but it maybe be a little more than that... I'm really...
View ArticleRe: All installation instructions not working
The only known reason for timeout is because of very heavy load situations, but in this case the following happens: 1. PirateBox reacts anymore for about 30 seconds. 2. All lights go off (reboot) 3....
View ArticleRe: PirateBox + COPS (Calibre OPDS (and HTML) PHP Server)
I checked the breaklog file and found this: PHP Warning: Module 'dom' already loaded in Unknown on line 0 PHP Warning: Module 'PDO' already loaded in Unknown on line 0 PHP Warning: Module 'pdo_sqlite'...
View ArticleRe: PirateBox + COPS (Calibre OPDS (and HTML) PHP Server)
I also tried doing some research and found this ( [stackoverflow.com] ) bit of information. I am not technically inclined enough to understand exactly what I need to do to fix this problem but if...
View ArticleRe: All installation instructions not working
No unfortunately, almost zero load. It was just shutting down for no reason. I'd have to unplug it and plug it back in to reboot it. No change in the lights, it just stops broadcasting SSID and...
View ArticleHow to install nano on OpenWRT ?
Hello from France ! :) I just made my own PirateBox this week, but I really don't like vim... How can I install nano on OpenWrt ? Thanks for helping :) Regards, Vinm
View ArticleRe: How to install nano on OpenWRT ?
salut! change the network config of your box and run /etc/init.d/piratebox nodns if your are able to ping Google.com and the ping does not show 192.168.1.1 as IP, then run opkg update opkg install...
View ArticleRe: How to install nano on OpenWRT ?
Thank you very much for this fast answer ! :) Okay, so I've just to use opkg as apt in Debian... Good, i did't want to use vim once again :p Vinm.
View ArticlePirateBox creation based on TP-Link MR3020
After playing with this PirateBox installation procedure and being unlucky multiple time, I can deliver some information on how the system is built. which can help you to understand faster and avoid...
View ArticleRe: Re-install ?
I took me some time to start dealing with the problem but everything work now. i just got a problem with the install command : so i used this one. Thanks a lot :) opkg install [piratebox.aod-rpg.de]...
View Article