Re: tl-mr13u HELP!
i have tl-mr13u and downloaded this firm [mega.co.nz] from this post [forum.openwrt.org] then i followed the instructions here [daviddarts.com] where while python mini installs the connection freezes...
View ArticleRe: tl-mr13u HELP!
Hi, today, I made some -not so nice- discoveries on the trunk images: [forum.daviddarts.com] :( Matthias
View ArticleMr3040 opkg help
I have a tp-link mr3040 v2.2, that i have openwrt trunk image installed on. I am trying to opkg install kmod-usb-storage kmod-fs-ext4 and block-mount. It says unknown packages also my opkg update is...
View ArticlePiratebox installed on TP-Link MR3020 - no wifi network shows up
Hello, So I have bought a TP-Link MR3020 to start hacking around with routers. I flashed the 12.09 build of OpenWRT on it and everything was fine. Yesterday I tried to install PirateBox on it...
View ArticleRe: Mr3040 opkg help
Hi, did you install the stock openwrt-trunk image from openwrt.org or did you use my custom image? Are you sure the internet connection of you fresh openwrt is working? does ping 8.8.8.8 work? Matthias
View ArticleRe: Piratebox installed on TP-Link MR3020 - no wifi network shows up
Hi, can you please post the output from the commands listed here Problem determination Thanks, Matthias
View ArticleRe: Piratebox installed on TP-Link MR3020 - no wifi network shows up
Thank you Matthias, I should have started with this! I used telnet to connect to my router in failsafe mode and typed the commands. I didn't go much further because apparently there's nothing about...
View ArticleRe: Piratebox installed on TP-Link MR3020 - no wifi network shows up
Hi, yes of course. If you boot on failsafe mode, you have a stock openwrt without any customization. Matthias
View ArticleRe: Piratebox installed on TP-Link MR3020 - no wifi network shows up
I can't access it if not in failsafe mode. How should I proceed? Thanks again
View ArticleRe: Mr3040 opkg help
Hi, I I used version 1 stock openwrt firmware, that I adjusted the byte size on in order to upgrade from the factory UI. I read this [wiki.openwrt.org] But was wondering if the reason why I can't opkg...
View ArticleRe: Mr3040 opkg help
I am actually trying to build a wifi pineapple out if the device. So if you don't have time to help don't worry your-self with it
View ArticleRe: Mr3040 opkg help
I can access web pages however ping google.com does not work. I tried a few different images including your custom image. Some images I ran into kernal issues. I did get the furtherest into the build...
View ArticleRe: Piratebox installed on TP-Link MR3020 - no wifi network shows up
First of all, double check your IP configuration. For this, you need to boot in failsafe mode, login then run the following command: mount_root Then double check your network configuration. - If there...
View ArticleClik here to view.
WR703N PB / USB Issues
Hello Everyone, Merry Christmas and hope that everyone has a good new years planned too :D Right, so, I have followed the install instructions for the WR703N version of PB on my router however, when I...
View ArticleDid I waste $35?
Hello all. I have been reading about the Piratebox for awhile, and wanted to make one...so when I scrapped up enough money for a TP-Link MR3020 and a 16gig flashdrive, I ordered them and they just got...
View ArticleNeed serious help...
Originally posted this to the wrong place, I believe, so trying again here. Hello all. I have been reading about the Piratebox for awhile, and wanted to make one...so when I scraped up enough money...
View ArticleRe: Did I waste $35?
Hi, stay calm and use failsafe mode: Recover via Failsafe mode B)- Regards Matthias
View ArticleRe: WR703N PB / USB Issues
Hi, thank you for you detailed post. you are using an image from madox.net, that webpage seems to have compiled the needed packages for piratebox, so they are not in their repository. You may use the...
View Article