Re: install packages from openwrt repository onto pirate box
Hi, ganastor's command is correct. I only want to extend it, as you might want to install the software onto the usb stick instead directly of the flash disk opkg -d ext install packagename.ipk best...
View ArticleRe: MR3040 lost cause?
It gave a prompt to give a login and password when I used ssh. when i try telnet 192.168.1.1 it gives me"network error:connection refused" . and ive tried to get it into failsafe with no luck. turn it...
View ArticleRe: MR3040 lost cause?
I may not have suggestions myself but did find a few links that may help at least... one of them is openwrt's official one. [harloholm.es] [wiki.openwrt.org]
View ArticleRe: MR3040 lost cause?
Keep trying to get into failsafe mode, your box is fine, only the password is lost. Remember to connect via wire AND setup a static IP address to your ethernet port. Without that, it won't work
View ArticleRe: install packages from openwrt repository onto pirate box
Thanks for the correction :) I had modified my install to include a swap space and I did a pivot root so it was all installed on the usb, in anticipation of my future tinkering.
View ArticleRe: Auto-install not working MR3040
Hello everybody, same happened to me, plus I try many ways to install the Pirate Box, and now by mistake I delete my ip address in the back loop and I cant logging back to the Openwrt with ssh...
View ArticleRe: Auto-install not working MR3040
When you ping 192.168.1.1 do you get a response? I can try to help but need more details than "I can't log in". Is it just telling you your password is wrong, or not getting a response at all? What...
View ArticleRe: Unbrick a TP-WR1043ND v2
Hi :) To begin I would like to thank every one who try to help me, It's very pleasant :) I'm sorry for this period of silence, I got a head full of shit about this brick.. After many days i try this :...
View ArticleRe: MR3040 lost cause?
Ok i finally got in through telnet. Thank you so much! new problem though. Links are saying to mount_root but when i do i get /sbin/mount_root: line 1: pi_include:not found /sbin/mount_root: line 1:...
View ArticleRe: TP Link MR3040 error
Hi I bought a another MR3040 and configured. Install went well. I followed the steps as outlined in [www.piratebox.cc] (I am using a 32gb microsd card connected through a usb convertor). I am able to...
View ArticleRe: Unbrick a TP-WR1043ND v2
did you tried the "WAN" port on the WR1043ND ? best regards Matthias
View ArticleRe: MR3040 lost cause?
The error messages are ok, just do mount_root passwd sync reboot -f then reboot and you should be able to login via ssh username root and your chosen password. you might also try this reflash with usb...
View ArticleRe: TP Link MR3040 error
When you are able to login to your system, can post the output of the following debug commands please Troubleshoot - technical summary thanks
View ArticleRe: Unbrick a TP-WR1043ND v2
Matthias Wrote: ------------------------------------------------------- > did you tried the "WAN" port on the WR1043ND ? > > best regards > Matthias Hi :) Yes I tried. I tried with another...
View ArticleRe: Unbrick a TP-WR1043ND v2
good! Please post the output of these commands executed on your router here.
View ArticleRe: Unbrick a TP-WR1043ND v2
That's the output : root@OpenWrt:~# mount rootfs on / type rootfs (rw) /dev/root on /rom type squashfs (ro,relatime) proc on /proc type proc (rw,noatime) sysfs on /sys type sysfs (rw,noatime) tmpfs on...
View ArticleRe: MR3040 lost cause? [Solved]
Thank you so much Matthias! And thanks for the suggestion ganastor! I followed your instructions and after i rebooted i put it back in failsafe. realized not what i meant to do so i rebooted and let...
View ArticleRe: Unbrick a TP-WR1043ND v2
Thank you for posting the output. Why does your usb stick has two partition? And what filesystem is the first partition? This seems totally wrong configured. best regards
View ArticleRe: MR3040 lost cause? [Solved]
Congratz! Just follow the upgrade instruction [www.piratebox.cc]
View Article